000 | nam k | |
001 | 2210080056492 | |
005 | 20140627121432 | |
007 | ta | |
008 | 880306s1981 bnka m FB 000a kor | |
040 | ▼a221008 | |
041 | ▼akor▼beng | |
056 | ▼a530.95▼24 | |
100 | ▼a공명달 | |
245 | 00 | ▼aMRP技法에 의한 生産-在庫시스템의 硏究 /▼d孔明達 著 |
260 | ▼a부산:▼b東亞大學校 大學院,▼c1981 | |
300 | ▼a83 p.:▼b삽도;▼c26 cm. | |
502 | ▼a학위논문(석사)--▼b東亞大學校 대학원:▼c工業經營學 전공,▼d1981년 12월 | |
520 | ▼b영문초록 : In traditional approaches to inventory management such as EOQ technique, the demand of component parts to a finished product was calculated by forecasting, so that forecast error would be created, and then carried excess inventory to compensate for it, but once the demand of the finished product was calculated by forecasting, it must be carried to minimum inventory by receiving the right quantity of components at the right time through a series of rational requirements-calculation procedure, since it is certain that the dependent demand of component parts with regard to the product is determined directly. From this point of view, this study tried to apply MRP technique to a valve X being produced by P manufacturing industry. The results obtained from this study were summarized as follows: 1) In case of item a, the reduced ratio in total variable cost and inventory was 8.0%, 63%, respectively, compared with the current control technique. 2) In case of item C, the reduced ratio in total variable cost and inventory was 4.5%, 8.9%, respectively, compared with the current control technique. 3) In case of item d, the reduced ratio in total variable cost and inventory was 16.9%, 35.2%, respectively, compared with the current control technique. 4) The greater magnitude of demand to end item, which its form is discrete, is fluctuated, the larger total variable cost and inventory reduce. These results were, however, obtained by observing and analysing the data only concerned with the special product of the special company and were supposed to be restrictedly applicable. It is therefore proposed that further studies remain available to investigate into the applicability of abovementioned results to other products. Besides, in operating and manipulating MRP system, in case that a corresponding item is voluminous and complex in assembly level, computer-aided solution procedures, for major items obtained from ABC classification method, will be desired and a sufficient computerization backup will be required for rescheduling due to changes of conditions in order to react flexibly to them. | |
650 | ▼a생산-재고시스템의▼a연구 | |
856 | ▼adonga.dcollection.net▼uhttp://donga.dcollection.net/jsp/common/DcLoOrgPer.jsp?sItemId=000002142345 | |
950 | ▼aFB | |
950 | ▼a비매품▼b₩3000▼c(추정가) |
Registration no. | Call no. | Location Mark | Location | Status | Due for return | Service |
---|---|---|---|---|---|---|
Registration no.
E0173345
|
Call no.
530.95 공34M
|
Location Mark
D
|
Location
부민학위논문실
|
Status
대출불가 (소장처별 대출 불가)
|
Due for return
|
Service
|
Registration no.
E0533862
|
Call no.
530.95 공34M =3
|
Location Mark
D
|
Location
부민학위논문실
|
Status
대출불가 (소장처별 대출 불가)
|
Due for return
|
Service
|