| 000 | nam k | |
| 001 | 2210080120417 | |
| 005 | 20140708141624 | |
| 007 | ta | |
| 008 | 870523s1986 bnka FB 000a kor | |
| 040 | ▼a221008 | |
| 041 | ▼akor▼beng | |
| 056 | ▼a552.3▼24 | |
| 100 | ▼a김웅장 | |
| 245 | 00 | ▼a1050 알루미늄의 切削特性에 미치는 切削條件의 影響 /▼d金雄章 |
| 260 | ▼a부산:▼b東亞大學校 大學院,▼c1986 | |
| 300 | ▼a37 p.:▼b삽도;▼c27 cm | |
| 502 | ▼a학위논문(석사)--▼b東亞大學校 大學院:▼c機械工學科,▼d1986. 2 | |
| 520 | ▼b영문초록 : This study has been carried out to clarify specific cutting force, chip shape and surface roughness. They were varied by cutting speed, feed and tool rake angle in the turning cutting experiment of 1050 Aluminium material with using tungsten carbide tools (G_(2)). The results obtained in this study are as follows; 1. Specific cutting fore decreases with the increase of cutting speed and feed. 2. Discontinuity of specific cutting force exists, and ocurrs at the low speed region as back rake angle is small. The range of discontinuity is being short with the increase of back rake angle. 3. According to the increase of cutting speed and feed, the shape of chip is changed into shear type, tear type, tear plus flow type, flow type in turn. 4. Surface roughness is good at the cutting speed, 500m/min and is nearly independent of the back rake angle. | |
| 650 | ▼a절삭가공 | |
| 856 | ▼adonga.dcollection.net▼uhttp://donga.dcollection.net/jsp/common/DcLoOrgPer.jsp?sItemId=000002141558 | |
| 950 | ▼aFB | |
| 950 | ▼a비매품▼b￦2400▼c(추정가) |
1050 알루미늄의 切削特性에 미치는 切削條件의 影響
종류
학위논문 동서
서명
1050 알루미늄의 切削特性에 미치는 切削條件의 影響
저자명
발행사항
부산: 東亞大學校 大學院 1986
형태사항
37 p: 삽도; 27 cm
학위논문주기
학위논문(석사)-- 東亞大學校 大學院: 機械工學科, 1986. 2
주기사항
영문초록 : This study has been carried out to clarify specific cutting force, chip shape and surface roughness. They were varied by cutting speed, feed and tool rake angle in the turning cutting experiment of 1050 Aluminium material with using tungsten carbide tools (G_(2)). The results obtained in this study are as follows; 1. Specific cutting fore decreases with the increase of cutting speed and feed. 2. Discontinuity of specific cutting force exists, and ocurrs at the low speed region as back rake angle is small. The range of discontinuity is being short with the increase of back rake angle. 3. According to the increase of cutting speed and feed, the shape of chip is changed into shear type, tear type, tear plus flow type, flow type in turn. 4. Surface roughness is good at the cutting speed, 500m/min and is nearly independent of the back rake angle.
관련 URL